Sökning: "Heat resistance"

Visar resultat 6 - 10 av 278 avhandlingar innehållade orden Heat resistance.

1. 6. Heat transfer phenomena and mould flux lubrication in continuous casting of steel

   Författare :Akira Yamauchi; KTH; []
   Nyckelord :Heat Transfer; Thermal Conductivity; Contact Resistance; Mould Flux; Solidification; Lubrication; Infiltration; Friction; Shear Stress; Modeling; Crystallization; Rupture Strength; Solidus; High-Speed Casting; Viscosity; Elasticity; Uniform Cooling;

   Sammanfattning : Overall thermal resistance of the mould flux was measured tomake clear the influence of the mould flux properties on theheat transfer behavior in continuous casting, especiallythermal conductivity and the formation of air gaps in thisstudy. From the investigation of the effect of the mouldsurface temperature and physical properties of the mould fluxon heat transfer through the flux film, following knowledge hasbeen obtained. LÄS MER

3. 7. Control of Wear-Resistance Properties in Ti-added Hypereutectic High Chromium Cast Iron

   Författare :Qiang Liu; Pär Jönsson; Keiji Nakajima; José Tinoco; KTH; []
   Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; High Chromium Cast Iron; cooling rate; Ti addition; M7C3; TiC; carbides size distributions; volume fraction; heat treatment; microstructure; mechanical properties; wear resistance;

   Sammanfattning : High chromium cast iron (HCCI) is considered as one of the most useful wear resistance materials and their usage are widely spread in industry. The wear resistance and mechanical properties of HCCI mainly depend on type, size, number, morphology of hard carbides and the matrix structure (γ or α). LÄS MER

4. 8. Turbulent Forced Convection Air Cooling of Electronics with Heat Sinks Under Flow Bypass Conditions

   Författare :Hans Jonsson; KTH; []
   Nyckelord :forced convection; heat transfer; pressure drop; turbulent; air cooling; bypass; plate; strip; pin; fin; heat sink; electronics; experimental; numerical; CFD; TECHNOLOGY; TEKNIKVETENSKAP;

   Sammanfattning : Air cooling is still the dominant method for dissipating theheat produced by electronic components. In a typical electronicdevice, the components are situated on a Printed Circuit Board(PCB). For most applications natural convection is sufficientto cool the components. LÄS MER

5. 9. Corrosion testing of heat exchanger tubing

   Författare :Ulf Kivisäkk; KTH; []
   Nyckelord :corrosion testing; heat exchanger; stainless steels; general corrosion; immersion testing; activation; stress corrosion cracking; constant load; u-bends; relaxation; dewpoint corrosion;

   Sammanfattning : Heat exchanger tubes are commonly made from stainless steel.In a heat exchanger both the process fluid and the cooling orheating media can be corrosive. It is therefore important to beable to select materials that do not suffer from corrosion.Current methods in this area, however, suffer from limitationsand shortcomings. LÄS MER

7. 10. Effects of manufacturing chain on mechanical performance : Study on heat treatment of powertrain components

   Författare :Johan Fahlkrans; Arne Melander; Bengt Lindberg; Stefan Jonsson; KTH; []
   Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; Heat treatment; case hardening; carburising; induction hardening; gas quenching; tempering; straightening; fatigue strength; contact fatigue; fracture mechanics; Industriell ekonomi och organisation; Industrial Economics and Management; Production Engineering; Industriell produktion; Teknisk materialvetenskap; Materials Science and Engineering;

   Sammanfattning : The increasing demands for lightweight designs with high strength call for improved manufacturing processes regarding heat treatment of steel. The manufacturing process has considerable potential to improve the mechanical performance and to obtain more reliable results with less variation. LÄS MER