Sökning: "plastic deformation"

Visar resultat 1 - 5 av 230 avhandlingar innehållade orden plastic deformation.

  1. 1. Microstructural Evolution In As-cast Alloys during Plastic Deformation

    Författare :Mitra Basirat; Pär Jönsson; Hasse Fredriksson; Jacques Lacaze; KTH; []
    Nyckelord :plastic deformation; compression test; recrystallization; deformation band; As-cast; microsegregation; carbide dissolution; disordered structure; order disorder transformation; twining; steel; β brass; copper; SRA - E-Science SeRC ; SRA - E-vetenskap SeRC ;

    Sammanfattning : The effect of deformation on microstructural changes in metals and alloys is the subject of considerable practical interest. The ultimate goal is to control, improve and optimize the microstructure and texture of the finished products produced by metal forming operations. LÄS MER

  3. 2. Microstructure and plastic deformation of textured CVD alumina coatings

    Författare :Siamak Shoja; Chalmers University of Technology; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; ENGINEERING AND TECHNOLOGY; α-Al2O3; Texture; Coatings; TKD; Plastic deformation; Deformation mechanisms; Electron microscopy; CVD;

    Sammanfattning : It is known that the wear performance of α-alumina coatings produced by chemical vapor deposition (CVD) is significantly influenced by the type and degree of texture. However, the main reasons behind this behavior are not fully understood. This thesis contains studies of two related topics for increasing the understanding of α-alumina coatings. LÄS MER

  4. 3. Torque and Angle Controlled Tightening of Bolted Joints

    Författare :Göran Toth; Chalmers University of Technology; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; torque controlled tightening; deformation parameters; momentary elongation; deformation factor; torque; Bolted screwed joints; spring characteristic; Torx; torque and angle controlled tightening; hexalobular; final torque; snug torque; Taylor’s series expansions; preload; plastic deformation; permanent elongation; yield; friction diameter; plastic spring constant; clevis; turn-of-nut method; bearing surface pressure; twisting; Monte-Carlo simulations;

    Sammanfattning : Reduced weight and fuel consumption, improved reliability and engine performance are the main requirements in the automotive industry of today. These requirements demand robust and optimized bolted joints, where a high amount of preload obtained by effective utilisation of the bolt is essential. LÄS MER

  5. 4. Changes in microstructure during plastic deformation of hardmetals

    Författare :Gustaf Östberg; Chalmers University of Technology; []
    Nyckelord :plastic deformation; APFIM; microanalysis; SEM; EBSD; TEM;

    Sammanfattning : .... LÄS MER

  7. 5. Influences of the Graphite Phase on Elastic and Plastic Deformation Behaviour of Cast Irons

    Författare :Torsten Sjögren; Ingvar L. Svensson; Sten Johansson; Jorge Sikora; Linköpings universitet; []
    Nyckelord :ENGINEERING AND TECHNOLOGY; TEKNIK OCH TEKNOLOGIER; TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; Cast iron; Flake graphite; Compacted graphite; Spheroidal graphite; Elastic deformation; Plastic deformation; Modulus of elasticity; Graphite modulus of elasticity; Strength coefficient; Strain hardening exponent; Acoustic emission; Construction materials; Konstruktionsmaterial;

    Sammanfattning : The amount and morphology of the graphite phase largely controls the resulting properties of cast iron. For instance, in flake graphite cast irons the mechanical properties are low while the thermal conductivity is high. LÄS MER