Sökning: "Uniaxial tension"

Visar resultat 1 - 5 av 32 avhandlingar innehållade orden Uniaxial tension.

  1. 1. Effects of Steel Fibres on Cracking in Reinforced Concrete

    Författare :Anette M Jansson; Chalmers tekniska högskola; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; uniaxial tension test; Keywords: Self-compacting; characteristic crack width; fibre-reinforced; bond; tension stiffening; Digital Image Correlation; pull-out test;

    Sammanfattning : ABSTRACTAlthough it is well known that fibre reinforcement acts as a crack arresting agent, there is still a need for deeper knowledge of the actual cracking behaviour, especially regarding cracks with widths smaller than 0.3mm. LÄS MER

  3. 2. Utilization of Andean grain flours in the development of wheat flour dough

    Författare :Sander Jonathan Pérez Villarroel; Avdelningen för livsmedel och läkemedel; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; LANTBRUKSVETENSKAPER; AGRICULTURAL SCIENCES; Wheat; Andean grains; Amaranth; Amaranthus caudatus; Canahua; Chenopodium pallidicaule; Quinoa; Chenopodium quinoa; Dough; Substitution; Ultracentrifugation; Phase separation; Dough composition; Macroscopic separation; Freezable water; Textural properties; Compression; Uniaxial tension; Biaxial tension; Principal component analysis; Partial least square regression; Bread;

    Sammanfattning : Bread dough was studied in relation to three Andean grain flours, quinoa (Chenopodium quinoa), amaranth (Amaranthus caudatus) and canahua (Chenopodium pallidicaule), as partial replacements for wheat flour with the perspectives of dough and breadmaking. This thesis deals with the understanding of both dough as a complex system, consisting of various water-filled polymers, and dough as a viscoelastic material, with different responses to deformations, in order to contribute to possibilities for improvements in dough analysis and development of novel products. LÄS MER

  4. 3. Modelling of Inelastic Effects in Metal Sheets and Identification of Material Parameters

    Författare :Edin Omerspahic; Chalmers tekniska högskola; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; plasticity; viscoplasticity; MCR mechanism; constitutive modelling; mixed hardening; damage; dynamic yield surface; material parameter identification;

    Sammanfattning : The continuum modelling of the macroscopic behaviour of metallic sheets and the identification of corresponding material parameters for models selected are dealt with in the thesis. Thermodynamics with internal variables provides a framework for the derivation of the models. LÄS MER

  5. 4. Mechanical properties of flax fibers and their composites

    Författare :Edgars Sparnins; Luleå tekniska universitet; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; Polymeric Composite Materials; Polymera konstruktionsmaterial;

    Sammanfattning : Flax fibers, along with a number of other natural fibers, are being considered as an environmentally friendly alternative of synthetic fibers in fiber-reinforced polymer composites. A common feature of natural fibers is a much higher variability of mechanical properties. LÄS MER

  7. 5. Mechanical behaviour of a roller bearing steel : Strength differential effect, low temperature creep and propagation of short cracks

    Författare :Irene Linares Arregui; Bo Alfredsson; Nils-Gunnar Ohlson; KTH; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY;

    Sammanfattning : Fatigue cracks in bearings either initiate from the surface or from an inclusion below the rolling contact surface. Then, short cracks start to propagate. Short crack grow at considerably faster rates than long cracks subjected to a nominally equivalent stress intensity factor range. LÄS MER