Sökning: "wear resistance"

Visar resultat 6 - 10 av 149 avhandlingar innehållade orden wear resistance.

  1. 6. Wear mechanisms in sheet metal forming : Effects of tool microstructure, adhesion and temperature

    Författare :Anders Gåård; Pavel Krakhmalev; Jens Bergström; Ulf Olofsson; Karlstads universitet; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; Galling; sheet metal forming; wear; friction; adhesion; temperature; Materialteknik; Materials Engineering;

    Sammanfattning : The general trend in the car body manufacturing industry is towards low-series production and reduction of press lubricants and car weight. The limited use of lubricants, in combination with the introduction of high and ultrahigh-strength sheet materials, continuously increases the demands on the forming tools. LÄS MER

  3. 7. Control of Wear-Resistance Properties in Ti-added Hypereutectic High Chromium Cast Iron

    Författare :Qiang Liu; Pär Jönsson; Keiji Nakajima; José Tinoco; KTH; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; High Chromium Cast Iron; cooling rate; Ti addition; M7C3; TiC; carbides size distributions; volume fraction; heat treatment; microstructure; mechanical properties; wear resistance;

    Sammanfattning : High chromium cast iron (HCCI) is considered as one of the most useful wear resistance materials and their usage are widely spread in industry. The wear resistance and mechanical properties of HCCI mainly depend on type, size, number, morphology of hard carbides and the matrix structure (γ or α). LÄS MER

  4. 8. Influence of Microstructure in Machining of Nickel and Nickel-Iron Based Alloys

    Författare :Stefan Olovsjö; Chalmers tekniska högskola; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; Wear mechanisms; Simulation; Tool wear; Burr; Meta-modelling; Inconel 718; Metal cutting; Superalloy; Waspaloy; Chip morphology; Notch wear; Alloy 718; JMatPro;

    Sammanfattning : Superalloys are used in applications such as turbines, steam power plants and nuclear power systems in components that require good high temperature properties and/or corrosion resistance. They are classified as difficult-to-cut materials and hence, from a sustainable production point of view, tool wear and tool life are major factors when machining these alloys. LÄS MER

  5. 9. Microstructure and Properties of Additively Manufactured Tool Steels for Hot Stamping

    Författare :Miwen Yuan; Chalmers tekniska högskola; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; Tool Steels; Wear; Hot stamping; Additive Manufacturing; Softening Resistance;

    Sammanfattning : Hot work tool steels are commonly used to produce dies for hot stamping, where the steels are exposed to cyclic thermal and mechanical loads. There is a constant demand to improve the lifetime of the dies. Additive manufacturing (AM) provides new solutions for tool design. LÄS MER

  7. 10. Machinability variations in Alloy 718 —With focus on machining of turbine components

    Författare :Pajazit Avdovic; Industriell Produktion; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; polar diagram; flank wear; ceramic tool; variation in material; tool wear; tool life; machinability; Inconel; Alloy 718; Machining; notch wear;

    Sammanfattning : In gas turbine engine, nickel base alloy, such as Alloy 718, accounts for almost half of the total material requirement. Nickel-base superalloys are used for gas turbine components mainly because of their outstanding strength and resistance to oxidation at high temperatures (> 550°C). LÄS MER