Sökning: "vibration and acoustic engineering vacuum technology maskinteknik hydraulik vakuumteknik vibrationer"

Visar resultat 21 - 25 av 45 avhandlingar innehållade orden vibration and acoustic engineering vacuum technology maskinteknik hydraulik vakuumteknik vibrationer.

  1. 21. Finite Element Procedures in Modelling the Dynamic Properties of Rubber

    Författare :Anders K Olsson; Byggnadsmekanik; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; akustik; vibration and acoustic engineering; Materiallära; materialteknik; Mechanical engineering; hydraulics; vacuum technology; Material technology; dynamic; amplitude; frequency; Technological sciences; Teknik; FEM; rubber; vibrationer; vakuumteknik; Maskinteknik; hydraulik;

    Sammanfattning : Rubber is not only a non-linear elastic material, it is also dependent on strain rate, temperature and strain amplitude. The non-linear elastic property and the strain amplitude dependence give a non-linear dynamic behavior that is covered by the models suggested in this thesis. LÄS MER

  3. 22. Thermodynamic Modelling and Performance of Combined Solid Oxide Fuel Cell and Gas Turbine Systems

    Författare :Jens Pålsson; Kraftverksteknik; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; vakuumteknik; vibrationer; akustik; Motors and propulsion systems; Motorer; framdrivningssystem; Gases; fluid dynamics; plasmas; plasma; hydraulik; Maskinteknik; vibration and acoustic engineering; hydraulics; vacuum technology; Modelling; Mechanical engineering; Solid oxide fuel cell; Hybrid system; Gaser; fluiddynamik;

    Sammanfattning : Solid oxide fuel cells (SOFCs) are a ceramic type of fuel cell operating at elevated temperatures. By utilising the thermal energy from the SOFC in a heat engine, a hybrid cycle with high performance can be achieved. One promising concept is a pressurised SOFC in combination with a recuperated gas turbine cycle. LÄS MER

  4. 23. Modeling and Performance of Gas Turbine Cycles with Various Means of Blade Cooling

    Författare :Kristin Jordal; Kraftverksteknik; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; fluid dynamics; Gases; termodynamik; Termisk teknik; applied thermodynamics; Thermal engineering; blade cost; HAT cycle; humid air; model validation; blade cooling modeling; thermodynamic simulations; blade cooling; Gas turbine; plasmas; Gaser; fluiddynamik; plasma; Mechanical engineering; hydraulics; vacuum technology; vibration and acoustic engineering; Maskinteknik; hydraulik; vakuumteknik; vibrationer; akustik;

    Sammanfattning : A method for simulating the cooled gas turbine is demonstrated. Based on equations and other knowledge found in the literature, a first-law thermodynamic, non-dimensional model is established and implemented in the equation-solving, programmable software IPSEpro. LÄS MER

  5. 24. Condition-Based Maintenance: Selection and Improvement of a Cost-Effective Vibration-Based Maintenance Policy for Rolling element Bearings

    Författare :Basim Al-Najjar; Sherwin David; Bo Bergman; Produktionsekonomi; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; vibration and acoustic engineering; vacuum technology; hydraulics; Mechanical engineering; a cost-effective vibration-based maintenance policy.; Integrated maintenance; Condition monitoring and control; Total Time on Test-plots; Vibration monitoring; effectiveness and accuracy; Failure causes and mechanisms; Maintenance quality; Maskinteknik; hydraulik; vakuumteknik; vibrationer; akustik; Commercial and industrial economics; Industriell ekonomi; Maintenance Technology; Terotechnology;

    Sammanfattning : Modern machinery is expensive and therefore must run at high availability and effectiveness which cannot be achieved without an effective maintenance policy. Condition monitoring, (CM), techniques can be utilised to reduce or arrest the rate of deterioration of a component so increasing operating life. LÄS MER

  7. 25. Numerical Investigation of Some Heat Transfer Topics with Relevance to Gas Turbines

    Författare :Arash Saidi; Värmeöverföring; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; vakuumteknik; Maskinteknik; vacuum technology; vibration and acoustic engineering; hydraulics; Mechanical engineering; plasma; fluiddynamik; Gaser; Ribbed ducts; intercoolers; EASM; EVM; gas turbine; CFD; heat exchangers; extended surfaces; offset strip fin; heat transfer enhancement; Thermal engineering; applied thermodynamics; Termisk teknik; hydraulik; termodynamik; Gases; plasmas; fluid dynamics; vibrationer; akustik;

    Sammanfattning : The first part of the investigation is related to the heat transfer and fluid flow problem inside ribbed ducts with a square cross section. The typical applications of this problem are in the cooling of gas turbine blades and guiding vanes. The second part is related to application of intercoolers in gas turbine systems. LÄS MER