Sökning: "surface treatments"

Visar resultat 31 - 35 av 266 avhandlingar innehållade orden surface treatments.

  1. 31. White Layer Formation during Hard Turning of Through-Hardened Martensitic and Bainitic AISI 52100 Steel

    Författare :Seyed Hosseini; Chalmers tekniska högskola; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; white layers; residual stresses; phase transformation; dynamic recovery; bainite; dynamic recrystallization; carbide deformation; retained austenite; steel; martensite;

    Sammanfattning : Increased demands for flexible manufacturing lines, shorter cycle times and reduced impact on the environment drives the need for optimization of today’s manufacturing. For machining of hardened steel parts (>45 HRC), grinding has been the obvious choice for many decades. However, hard turning has often been considered as a replacement due to e. LÄS MER

  3. 32. Additive-Driven Improvements in Interfacial Properties and Processing of TMP-Polymer Composites

    Författare :Seyedehsan Hosseini; Chalmers tekniska högskola; []
    Nyckelord :NATURVETENSKAP; NATURAL SCIENCES; NATURVETENSKAP; NATURAL SCIENCES; TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; NATURVETENSKAP; NATURAL SCIENCES; TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; NATURVETENSKAP; NATURAL SCIENCES; TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; molybdenum disulfide; magnesium stearate; thermomechanical pulp; alkyl ketene dimer; friction; rheology;

    Sammanfattning : Efforts to address environmental concerns have resulted in new regulations designed to plan the reduction of plastic and synthetic polymer usage, necessitating the search for sustainable natural alternatives with comparable cost-effectiveness and mechanical performance. Thermomechanical pulp (TMP) fibres are one of the most affordable natural fibres that have no chemical refining in production, production have a high yield of 90-98% and TMP fibres have been demonstrated to improve the mechanical characteristics (strength, stiffness and toughness) of wood-polymer composites (WPCs) compared to the pure polymer. LÄS MER

  4. 33. Performance of MCrAlX coatings : Oxidation, Hot corrosion and Interdiffusion

    Författare :Pimin Zhang; Ru Lin Peng; Xin-Hai Li; Sten Johansson; Ping Xiao; Linköpings universitet; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY;

    Sammanfattning : MCrAlY coatings (M=Ni and/or Co) are widely used for the protection of superalloy components against oxidation and hot corrosion in the hot sections of gas turbines. The drive for coating systems to bestow adequate oxidation and corrosion resistance upon the components becomes urgent as an inevitable result of the necessary improvement in engine combustion efficiency and service lifetime. LÄS MER

  5. 34. Effect of heat treatment on microstructure and mechanical properties of a 5 wt.% Cr cold work tool steel

    Författare :Arbab Rehan; Lars-Erik Svensson; Leif Karlsson; Anna Medvedeva; Per Erik Skogholm; Berne Högman; Reinhold Schneider; Högskolan Väst; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; Cold work tool steel; Hardening; Tempering; Microstructural characterisation; Retained austenite; Martensite; Bainite; Hardness; Impact toughness; Production Technology; Produktionsteknik; Manufacturing and materials engineering; Produktions- och materialteknik;

    Sammanfattning : This work presents investigations related to phase transformations occurring inthe 5 wt.% Cr cold work tool steel Caldie during hardening and tempering treatments. LÄS MER

  7. 35. Nanostructured carbon materials prepared by hole-mask colloidal lithography

    Författare :Hans Fredriksson; Chalmers tekniska högskola; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; NATURVETENSKAP; NATURAL SCIENCES; TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; NATURVETENSKAP; NATURAL SCIENCES; HOPG; GC; Colloidal Lithography; Oxygen; RIE; Nanofabrication;

    Sammanfattning : Research and development of nanofabrication methods can be motivated both formanufacturing of commercially available products like micro electronic componentsand for development of model systems for fundamental and applied science. Thefabrication process developed during this work, hole-mask colloidal lithography(HCL), is primarily oriented towards the latter two, specifically for research in thefields of catalysis, nanoparticle plasmons, and bio- and fundamental physics. LÄS MER