Sökning: "conventional binder tests"

Hittade 4 avhandlingar innehållade orden conventional binder tests.

  1. 1. Influence of waxes on bitumen and asphalt concrete mixture performance

    Författare :Ylva Edwards; Ulf Isacsson; Klaus-Werner Damm; KTH; []
    Nyckelord :ENGINEERING AND TECHNOLOGY; TEKNIK OCH TEKNOLOGIER; TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; bitumen; asphalt; additives; wax in bitumen; polyphosphoric acid in bitumen; rheology; IR-spectroscopy; dynamic mechanic analysis DMA ; bending beam rheometer BBR ; literature study; low temperature physical hardening; highway materials; morphology; modified bitumens; temperature susceptibility; low temperature performance; ageing; microscopy; chromatography; Fourier transform infrared spectroscopy; force ductility; conventional binder tests; asphalt performance; tensile strain restrained specimen test TSRST ; Building engineering; Byggnadsteknik;

    Sammanfattning : This doctoral thesis consists of a literature review, presented in two papers, and another six papers describing experimental studies of the influence of different kinds of wax and polyphosporic acid on bitumen and asphalt concrete mixture properties. The literature review should give an extensive description of the field of knowledge concerning wax in bitumen. LÄS MER

  2. 2. Thermally cured coil-coatings utilizing novel resins and fatty acid methyl esters as reactive diluents

    Författare :Katarina Johansson; Mats Johansson; Rolf van Benthem; KTH; []
    Nyckelord :NATURAL SCIENCES; NATURVETENSKAP; NATURVETENSKAP; NATURAL SCIENCES; Coatings; Coil-coatings; Thermal cure; Reactive diluents; Fatty acids; Transesterification; Hyperbranched polyester resins; Film properties; Polymer chemistry; Polymerkemi;

    Sammanfattning : Solvent-borne thermally cured coil-coating resins contain large amounts of volatile organic solvents in order to obtain suitable flow for film application. This work describes how the expensive and environmental hazardous volatile organic solvent content of a solvent-borne thermally cured polyester/melamine coil-coating system can be reduced by introduction of fatty acid methyl esters (FAMEs) as reactive diluents and modification of the polyester binder resin. LÄS MER

  3. 3. Characterization of WC-Co tools used for machining of Alloy 718 under the influence of high-pressure coolant supply

    Författare :Philipp Hoier; Chalmers University of Technology; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; erosion; surface-modifications; High-pressure coolant supply; Alloy 718; tool wear; vapor-barrier;

    Sammanfattning : The use of high-pressure jets for supply of coolant to the cutting zone has the potential to significantly increase the productivity and process stability when machining difficult-to-cut materials such as Ni-based superalloys. Apart from better chip-breakability, the jets enable the coolant to reach closer to the cutting edge and hence enhance its capability to dissipate heat. LÄS MER

  4. 4. Composite Bridges : Innovative ways of achieving composite action

    Författare :Robert Hällmark; Peter Collin; Ian May; Luleå tekniska universitet; []
    Nyckelord :ENGINEERING AND TECHNOLOGY; TEKNIK OCH TEKNOLOGIER; TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; Composite action; bridges; steel; concrete; shear connectors; prefabrication; coiled spring pins; shear studs; post-installation; design guidance; Structural Engineering; Konstruktionsteknik;

    Sammanfattning : The topic of this thesis is steel-concrete composite bridges and innovative ways of achieving composite action. The typical superstructure consists of three main components: the steel girders, the concrete deck slab and the shear connectors. LÄS MER