Sökning: "FE-analysis"

Visar resultat 11 - 15 av 57 avhandlingar innehållade ordet FE-analysis.

  1. 11. Structural Analysis Methods for the Assessment of Reinforced Concrete Slabs

    Författare :Jiangpeng Shu; Chalmers tekniska högskola; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; Bridge Deck; Finite Element FE Analysis; Shear and Punching; Structural Response; Reinforced Concrete Slabs; Multi-level Assessment Strategy;

    Sammanfattning : Reinforced concrete (RC) slabs are among the most critical parts of the load-carrying capacity of such structures as bridges and parking decks. Previous research indicated that the assessment methods used in current practices largely underestimated the load-carrying capacity. LÄS MER

  3. 12. Bridge Overhang Slabs with Edge Beams : LCCA and Structural Analysis for the Development of New Concepts

    Författare :José Javier Veganzones Muñoz; Costin Pacoste; Raid Karoumi; Lars Pettersson; Rui Vaz Rodrigues; KTH; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; Overhang slab; Edge beam; Life-cycle Cost Analysis; Non-linear FE-analysis; Design methods; Shear force; Failure mode; Effective width; Minimal width.; Konsolplattor; Kantbalkar; Livscykelkostnadsanalys; Icke-linjär FE-analys; Dimensioneringsmetoder; Tvärkrafter; Brott; Fördelningsbredd; Minimal bredd.; Bro- och stålbyggnad; Structural Engineering and Bridges;

    Sammanfattning : Bridge edge beams are associated with high life-cycle costs because of the need of maintenance, which also causes traffic disturbances. For this reason, the Swedish Transport Administration started a project to find better solutions. One of the proposals was a design without edge beam. LÄS MER

  4. 13. Use of FE-analysis for predicting and verifying the design of an automotive component forming process with special regard to macro geometric defects

    Författare :Alf Andersson; Industriell Produktion; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; information exchange; sheet-metal forminA simulation finite element analysis; springback surface defects Classflcation system and or Index term If any ;

    Sammanfattning : This thesis includes four appended papers. The thesis describes the challenges and advantages of the use of FE-analysis in the design of a component forming process in the automotive industry. LÄS MER

  5. 14. Improved Bridge Evaluation

    Författare :Hendrik Schlune; Chalmers tekniska högskola; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; model updating; structural identification; Bridge evaluation; concrete structures; finite element analysis; finite element method; load cases;

    Sammanfattning : Accurate structural models are required for optimal management of existing bridges and economical new ones. However, unavoidable modelling uncertainties and difficulty in modelling the non-linear response of concrete bridges can lead to structural models which do not fulfil this requirement. LÄS MER

  7. 15. Modelling and simulation of the roll forming process

    Författare :Michael Lindgren; Luleå tekniska universitet; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; Material Mechanics; Materialmekanik;

    Sammanfattning : One of the first decisions to make when a new roll forming line is designed is the number of forming steps needed to produce a profile. This is dependent on the material properties, the cross-section geometry and the tolerance requirements. LÄS MER