Sökning: "Axial Injection"

Visar resultat 1 - 5 av 16 avhandlingar innehållade orden Axial Injection.

  1. 1. Mitigation of Pressure Pulsations in Axial turbine draft tube with jet injection or solid rod protrusion: A Numerical investigation

    Författare :Henrik Holmström; Cécile Münch-Alligné; Luleå tekniska universitet; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; Vortex rope mitigation; vortex rope; Strömningslära; Fluid Mechanics;

    Sammanfattning : The introduction of intermittent renewable energy sources, such as wind and solar power, to the power grid, demands some hydraulic turbines to operate at unfavorable operating conditions not initially designed for. Strong swirl develops at loads below the best efficiency point, (BEP) due to angle mismatch between the guide vanes and the fixed runner blades typical for Francis and Propeller turbines. LÄS MER

  3. 2. Fundamental Studies on Direct Injection Nebulisers for Sample Introduction in ICP Spectrometry : Aerosol Properties, ICP Characteristics and Analytical Performance

    Författare :Daniel Goitom Asfaha; Wolfgang Frech; Ralph Edward Sturgeon; Umeå universitet; []
    Nyckelord :NATURVETENSKAP; NATURAL SCIENCES; ICP; ICP-MS; ICP-OES; sample introduction; DIHEN; Vulkan DIN; non-spectral interferences; noise power spectra; analytical precision; plasma diagnostic parameters; particle dynamic analysis PDA ; Analytical chemistry; Analytisk kemi;

    Sammanfattning : The performance of different types of nebulisers: Vulkan direct injection nebuliser (Vulkan DIN), direct injection high efficiency nebuliser (DIHEN), microconcentric nebuliser coupled to cyclonic or double pass spray chamber (MCN-C or MCN-DP, respectively) was investigated and compared when used for sample introduction to ICP-MS or ICP-OES. With ICP-OES, in axial viewing mode, intensity distributions across the radius of the plasma (radial intensity profiles) were determined for different spectral lines with Esum 1. LÄS MER

  4. 3. Computation of Thermal Development in Injection Mould Filling, based on the Distance Model

    Författare :Per-Åke Andersson; Linköpings universitet; []
    Nyckelord :NATURVETENSKAP; NATURAL SCIENCES; thermoplastic materials; finite element FEM ; finite difference FD ; Newton-Mysovskii theorem; Moldflow Mfl ; Cadmould Cmd ; MATHEMATICS; MATEMATIK;

    Sammanfattning : The heat transfer in the filling phase of injection moulding is studied, based on Gunnar Aronsson’s distance model for flow expansion ([Aronsson], 1996).The choice of a thermoplastic materials model is motivated by general physical properties, admitting temperature and pressure dependence. LÄS MER

  5. 4. Discogenic pain - A diagnostic challenge

    Författare :Hanna Hebelka; Göteborgs universitet; []
    Nyckelord :MEDICIN OCH HÄLSOVETENSKAP; MEDICAL AND HEALTH SCIENCES; discography; disc; disc pressure; low back pain; axial loaded MRI; validity;

    Sammanfattning : Low back pain (LBP) is a common health complaint with a lifetime prevalence up to 80%. Patients with discogenic pain constitute a minority of all with LBP but represent an important group with substantial personal consequences and high demands on health-care and social systems. LÄS MER

  7. 5. Design of Suspension Plasma Sprayed Thermal Barrier Coatings

    Författare :Ashish Ganvir; Nicolaie Markocsan; Mohit Kumar Gupta; Per Nylén; Christian Moreau; Högskolan Väst; []
    Nyckelord :TEKNIK OCH TEKNOLOGIER; ENGINEERING AND TECHNOLOGY; Microstructure; Thermal Barrier Coatings; Axial Injection; Suspension Plasma Spraying; Porosity; Thermal Conductivity; Fracture Toughness; Lifetime; Production Technology; Produktionsteknik; Manufacturing and materials engineering; Produktions- och materialteknik;

    Sammanfattning : Thermal barrier coatings (TBCs) are widely used on gas turbine components to provide thermal insulation, which in combination with advanced cooling, can enable the gas turbine to operate at significantly higher temperatures even above the melting temperature of the metallic components. There is a permanent need,mainly due to environmental reasons, to increase the combustion temperature inturbines, hence new TBC solutions are needed. LÄS MER